Workshop Cleanout and Electric

 So we last left off trying to figure out storage and heating solutions.  Well, we have made progress on both tasks.  My new storage unit is setup and I just moved the large crates into the storage unit for the time being.  This frees up all of my floor space in the garage, which may not be important for now, will make a major difference as I get into the larger parts.  I also just had the 240V line run for my new mini split unit that will be installed this week.  So despite a lull in build time due to the bitter cold, I am hoping to be back on the bandwagon next week.  I am looking forward to a great 2023 build year!

Storage and Heat..... Who Needs That?

 So My rudder is assembled and ready for the match drilling of ribs.  However the last month has been quite hectic with the holidays and winter approaching.  I haven't been in the garage too much because the temperatures have been getting down to the 30's and 40's, making for a very cold work session.  It's very difficult to work with fine motor skills at such low temperatures.  I have been in the process of getting quotes to install a mini split into my garage so I can make the workshop reasonable.  For those that don't know me, my attached garage is a 2.5 car garage and I prefer to avoid the flammable liquids/gases based systems.  As a firemen, I have seen numerous occasions of Carbon Monoxide poisoning in homes where these types of heating systems do not operate properly or the room doesn't ventilate well.  So I hope to have this heat settled in the next two weeks or so.

In other news, my wife has been on my case about getting her garage back for the winter.  With the fear of winter snow coming, my wife would like to be able to park in the garage during a storm.  As a result, I've been searching around for the best options for off site storage.  Most of the storage solutions near me are fully packed or only have smaller units.  After some searching and luck, I happened to come across a storage place who just actually had a tenant move out the day before.  This allowed me to snag a larger unit which gives me room to grow as the plane gets larger.  This also allows me to open up floor space as I build further into the project.  So I am hoping to be back on the bandwagon shortly and get the rudder finished up.

Rudder Match Drilling Prep and Storage Concerns

 I have been a bit busy with life the last two or three weeks.  Between work and family stuff, I haven't had a significant amount of time to get outside.  I also started to realize I need to plan for the winter accordingly.  My garage is insulated for the most part but has no heat source currently.  I am waiting for some quotes to get a Mini Split or Heater installed to allow me to work out there in the winter months.  It get a bit hard to work fine motor when its 30 or 40 degrees out.

Another thing I have realized is my wife wants her parking spot back.  My wife is very understanding and allows me to utilize the entire garage during the majority of the year, however, winter is coming.  As such, the boss has ordered me to make space for her car in prep any snow events.  As such, I spent a lot of time calling around to local storage places looking for a medium sized unit.  I figure if I can get rid of the two large crates, I can easily fit my wifes vehicle in the garage when needed.  However, finding a unit was a serious struggle.  Most of the ones I can find are very small and won't work for my needs, and the larger ones have one of two issues.  One issue was they were inside units with tight hallways to access, I didn't want to risk swinging a flight control or large part and denting it when I don't clear something.  Also, many of them were simply unavailable.

I eventually struck a bit of luck and happened to check a unit in the next town.  I asked about mid size units, but the only thing open was a large unit, which literally became available that day (it was the first of the month).  Since I haven't been able to find anything, I decided to take it.  My thought process was I have some extra space in back for some household stuff, but I have the large unit to grow into as I finish other parts.  It also will allow me to store some racks for small parts in a more organized way.  And I am buying some saw horses to build some "skin tables" to store skins flat until needed.  I am hoping to have the unit setup and everything moved sometime next week, which will allow me to focus on the rudder again.

In the meantime, I was able to finish the rudder prep and have the skins placed for match drilling.  This process wasn't terrible, lots of little prep work.  Separating the stiffeners and lots of deburring was in order to get to this point.  I constantly am debating about the level of deburring, many people seem to argue online about how "smooth" or how perfect things should be.  I find the cut pieces are a bit less precise but the stamped parts are pretty straight forward to deburr.  I don't feel any major sharp points or anything, so I think I am doing ok.  

Lots of deburring to get the structure together.

After a long deburring session, I got to clecoing the skin together.  It's amazing how precise the kit is, and match drilling should be pretty straight forward.  Another thing I am still trying to figure out is how crazy I need to be.  On the vertical stabilizer, I would simply run the drill in and out quickly, most parts were not taking much if anything off at all.  So do I need to waste time with this step every time or now?  The plans aren't updated to reflect what parts are final sized or not, so I have been cautious and making sure to do it quickly.  I guess this makes a more exact part anyway and makes riveting easier.  Should I just be reaming everything instead?  What do you guys think?

Rudder skin cleco'd in place.

So that's where I stand right now.  The rudder hasn't been too terrible, but I am looking forward to my first back riveting experience which will be coming soon.  Time to get back out there this week.

Chapter 7 Begins : The Rudder

 So we have completed the last remaining step of chapter 6 and have officially broken ground into chapter 7.  Chapter 7 is the Rudder, which will be mounted eventually to the back of the Vertical Stabilizer from chapter 6.  This piece uses some different and new building techniques which I did not get to use in chapter 6.  During this chapter I will do a bunch of backriveting, some pull rivets, rivet a trailing edge, and roll a skin.  I am looking forward to this, the only thing I didn't do in my fundamentals class was the actually adhesive that goes in the trailing edge.  On that note, I should go order that soon so its here when I get to that point.

Today I pulled out the beginning parts and got organized.  The first few steps of chapter 7 have me labeling the cut lines for separating the pieces.  Many of the pieces come together as on larger piece, and some need to be cut apart or trimmed down.  The directions are very clear and make the process easy, its just a tedious job making sure to line things up.  I wish I had a metal break as the did in Atlanta, but the cost isn't conducive to my light use.  Here are the pieces I had marked up which are ready for cutting.  This took me a little over an hour to get done.  Next session will be cutting and deburring all of these parts down. 

Marked Rudder Pieces - Pre-Cutting

Marked Rudder Pieces - Pre-Cutting

Another item on my to do list is to finish organizing the parts.  I have honestly been debating getting a storage unit but that is going to be about $150 a month.  I really don't want to do so yet but spaces are limited around my area and I don't want to miss out on the right size one.  Optimally, the unit will be large enough to store the bigger pieces as I finish them and other parts I don't need yet.  This will also free up much more garage space to allow for work once I get to the tail cone and bigger pieces.  I have to make some calls and see what's available.

Priming Take 2 and First Drilling

 So I had to redo my priming setup based on the issues found during my first session.  Luckily I had some scrap wood lying and I had an idea.  I went to the hardware store and got some wire netting which I stapled across the wood as a frame.  It allowed me to spray down and through the frame with no issues of sticking.  I quickly flipped the parts over and sprayed again without issue.

After ironing out my priming setup, I moved onto match drilling the J stiffeners.  They require you to mount at a specific measurement and drill along the length.  It is a lot of holes to match drill on one flange alone.  With some manipulating and moving as I went, it took me about an hour to do the top flange.  I am going to do all of the countersinking and river the nutplates before I flip the spar and do the bottom flange. I figured this would be easier instead of continuously flipping this spar over repetitively.  I now need to setup the counter sink cages and get those dialed in.

The new priming setup.  This worked much better than the paper itself.  

In other news, I received notification today that my empennage kit is finally shipping out today.  Its exciting to think that I will have a tail kit next week sometime.  However, I need to make space on the garage floor for it to sit.  My wing spars need to be stored appropriately and the minds at be seem to think storing them flat is optimal.  I am currently debating finishing the one wing so it can be put into the wing stand, but I am not sure.  I am very torn as it would be a great way to store the parts and open up additional space, however the work would take me quite awhile to do.  The other option is to put the spar back as it is, move some parts around and deal with the tail kit right away.  Either way I will be looking for space to store things as I continue building.  I'll post back what I decide to do in the next update.

DRDT Setup Finished and More Deliveries...

 So I got some time and finally made it to Lowes.  I was able to pickup some cheap carpet and cut it down.  I deliberately bought extra so I could cover the DRDT, Wing Stand, and some scrap to use as padding.  I still want to get a piece of ribbed carpet to act as a table runner on my workbenches.  I saw another builder who used that and it was convenient for when you dropped things as they would get caught between the ridges.  Regardless, I wrapped up the table in carpet and came across an issue.  The table dimensions really don't allow for the carpet depth, and as soon as I tried to put it over the frame, it wouldn't go down.  I ended up trimming the carpet to cover the tops and outside edges only, and ran it smooth to the middle edges.  I ran my hand all around and didn't notice anything sharp that will beat up the skins, but I plan to monitor it for a bit to be safe.  Anyone building this later, I'd recommend leaving a little space in the center gap to allow for the carpet or carpet across the top over the front.

Completed DRDT Table

After wrapping up the DRDT table, I got in my Stewart Products primer shipment.  My can of EkoPrime and EkoEtch arrived so I am now ready to start priming parts.  I looked into the first two sections of the wing build and thought about things I would need.  I have made my run to Harbor Freight for a Tap and Dye set for fabricating the tie downs and some other odds and ends.  I also have ordered some paint strainers and a vice for the table which should come in the next day or two.  I am hoping to start match drilling by the weekend.

In other thoughts, I also have been debating how to organize the garage.  I ended up buying two deep hooks to hand on the ceiling joist.  These allow me to hang the longer narrow pieces like J Channels, Spars, and such off the floor and out of the way until I need them.  The actual spar crate only has the two spars in it and I think I will be breaking that down soon.  My current though process is to build the wing stand sooner than later.  By building the wing stand, I can store the two spars horizontally together, put the larger skins underneath on the cart, and break down both crates for disposal.  This would open up the floor space for the empennage kit to arrive late next month sometime.  However, I looked through the plans and I think it might be wise to build in order versus jumping around.  It seems like if I prep the spars, I can then start adding things as I finish each section.

I also received my order from Van's for the leading edge kits.  I have decided to move forward and go with the FlyLED's lighting kits.  I am going to use the Original kit which is only Nav/Position and Strobe lights in the wingtips.  Then I will cut a hole in the leading edge in order to mount the FlyLED 7 star lights as my taxi and landing lights.  I have seen really great feedback on their products, the cost is significantly lower than ZipTips, and it can all be done myself without too much fuss or waiting for shipment.  I plan to order all of the lights when I get to the leading edge section so I can put them in with the skins off and not kill myself doing it after the fact.  The only thing I have to decide is whether I want to do the soldering and if I want to add the Cowl light designed specifically for the RV-10.  I plan to hold off on the Cowl light until the very end, but I will see how Guil from BuildFlyGo likes his setup.  He will be done well before me and I can get his thoughts on midline lighting as he isn't adding it for now.

Until next time...

Inventory.... Inventory... and More Inventory

 Well there is a lot of work to do with the kits once they arrive.  The first thing is opening the crate carefully as to not damage anything, remove the packing list, and then start to dig through the packing material.  Van's does an exceptional job of packaging so much stuff into these crates very carefully.  They use lots of tape and paper to secure everything so there is little to no movement of the parts during transit. As long as the crate stays intact (thats the big part), there seems to be a small chance of damage.  A few things I've noted:

• Look out for the shipper to mis-orient the crate.  My one crate arrived on its side despite clear markings for which side up..... and the truck was empty otherwise so there was no reason for it.
• Look for damage on the bottom and sides, the forklifts can do some good damage if they aren't careful.
• Open and unroll all the packing paper, they wrap things up and you don't want to throw away a part by accident.    
• When inventorying the larger parts, you will come across a few items that are not labeled.  These are mostly angle iron, tubes, and some other odd parts.  Set them aside and finish the rest of the inventory.  Once this is done, then compare the remaining few pieces to the inventory list. It will be pretty easy to identify them at this point.  Then take painters tape and label the item with the appropriate part number for later.
  
• Another item I found helpful was to mark out where you put things.  Depending on your workspace, you should have bins or shelves that are labeled.  Then mark on the inventory where these items are for easy location later.
• I had one part which was "warped" but its due to how the part is pressed in the punch at production.  Since I am doing the wing kit first, I have not received the first part of the manual and need to download the details for straightening in section 5.

I spent about 5 hours or so doing the small hardware alone and probably two hours doing the main kit pieces and subkits.  This took up the majority of the inventory time overall separating out the mixed bags and putting everything into storage bins.  I found the Harbor Freight bins really helpful for this.  I think the small bins are probably the most useful but I had purchased a few of the medium ones.  They are a bit big for some items, but I'd rather have the space for later when we get into bigger items like fuselage parts.  As well, my tail kit is expected next month so I will be hopefully combining some of the rivets and bolts into one bin for easy storage.  

I'll update this later with some pictures of the bins and how I marked things for reference.  Until next time.

Airventure 2021

 Well after a year off, Airventure has returned for 2021.  I unfortunately cannot attend with my work schedule this year, but I am definitely going next year.  My best friend and I have agreed that we will head out commercially and stay 3 days to explore.  I already am mentally building my list of the have to sees in the exhibition area.  I definitely want to stroll around the homebuilt areas and get to meet and pick the brains of the builders.  It would be really great to meet and talk with a few of the builders I followed that had inspired this project.  

I'll be honest, I've had Live ATC going the last three days monitoring the Fisk arrival and watching it on Foreflight's internet traffic.  I am disappointed I couldn't go, but glad that I have a plan for next year.  Any tips for finding a reasonable hotel would be appreciated, it appears most hotels only book a year out, so next summer hasn't quite opened yet.  

I also am looking to possibly find an RV-10 demo flight.  Van's has restarted their demo flights and I think its wise to reach out to Zach, the east coast rep, to try and setup something.  I can use it as another excuse for a cross country and it will help me wrap up this instrument rating as well.

Update on my Project Prep

I have been working on reorganizing the garage and getting ready for this.  I finally got the overhead storage and all of the shelving put up so I can get the floor cleared out.  This also made room for me to buy a brand new tool chest from Harbor Freight.  The US General tool bench is great and I bought an add on end cabinet to increase my storage.  As I get more of the garage cleaned out, I plan to get started on building the project table and the air piping.  I am hoping the lumber cost drops a bit before I start that build, but sometimes you need to just bite the bullet.  Until my next update... I'll try to remember and snap some pictures of the new shelving and workbenches.

Storage and Lighting

 Well the first prep task has been completed.  I bought some overhead shelving to mount over the garage doors.  I need to clear up the floor space so I can have enough room to build in the garage when I am ready.  The two racks were a bit interesting to put up, especially since the bars that support it are a bit flexible.  But with some persistence and hard work I finally got them up.  I expect this push through work ethic is going to be needed at many points through the project.  Now it's time to clean up the floor and get things up on the rack.

In other news, I have been debating my idea of a 10 and have also looked at the RV-14.  Part of my thinking is it would be easier to do a 2 seater aircraft and move upwards later, but part of me says why bother and just build the plane I want now.  Thoughts?

 Photo of RV-14 Demo plane by Flying Magazine.